CN/EN

河南名冠科学仪器有限公司

河南名冠科学仪器有限公司 | 广告语
mobile 18790258621
Home>Proudct Center > Lab Equipment > Film Coating Machine > Spin Coater >

MSK-USP-04C Ultrasonic Spray Pyrolysis Coater

MSK-USP-04C Ultrasonic Spray Pyrolysis Coater/Glue Sprayer uses a stepper motor and a microprocessor to control the volumetric pump to ensure accurate transmission of solutions through the infusion set and the continuity of ultrasonic spray process. An ultrasonic atomizer is used to prepare a thin micro-nano coating, and a stepper motor is used to control the atomizer to move in the X-axis and Y-axis directions, and the moving speed can be adjusted within a certain range to ensure the uniformity of coating on the substrate surface.



18790258621
product details

Ultrasonic Spray Pyrolysis Coater-MSK-USP-04C 

 Ultrasonic Spray Pyrolysis Coater.jpg

MSK-USP-04C Ultrasonic Spray Pyrolysis Coater/Glue Sprayer uses a stepper motor and a microprocessor to control the volumetric pump to ensure accurate transmission of solutions through the infusion set and the continuity of ultrasonic spray process. An ultrasonic atomizer is used to prepare a thin micro-nano coating, and a stepper motor is used to control the atomizer to move in the X-axis and Y-axis directions, and the moving speed can be adjusted within a certain range to ensure the uniformity of coating on the substrate surface.

 

Main Features

The atomization method is to spray the solution onto the substrate after atomization, so as to obtain the desired material structure. This material preparation method is particularly suitable for depositing oxides and has a long history of application in the preparation of transparent electrodes. Now this method is widely used in the preparation of perovskite solar cells.

 

 

Technical Parameters

Product Name

MSK-USP-04C Ultrasonic Spray Pyrolysis Coater/Glue Sprayer

Product Model

MSK-USP-04C

Installation Conditions

This equipment is required to be used at an altitude of 1000m or less, a temperature of 25℃±15℃, and a humidity of 55%Rh±10%Rh.

1. Water: NOT needed

2. Electricity: AC220V 50Hz, must have good grounding

3. Gas: The nozzle of the equipment is pneumatically assisted, and an air compressor or gas cylinder (including a pressure reducing valve) is required.

4. Workbench: floor type, covering an area of more than 2m2

5. Ventilation device: needed

Main Parameters

(Specification)

1. Power supply: 220V  50Hz/60Hz

2. Ultrasonic atomizer: 40KHz 100W

3. Travel distance of sprayer on X axis and Y axis: 1mm-200mm

4. Moving speed of sprayer: 10mm/s-800mm/s in X-axis direction, 10mm/s-100mm/s in Y-axis direction

5. Size of coating colloid particles: 10um-20um

6. Flow rate: 0.6pl~4ml/min

7. Solid content: ≤ 10%

8. Viscosity: ≤ 100cPs

9. Space between layers: 1mm-100mm

10. Max adjustment of Z-axis height: 60mm

11. Size of heating plate: 350mm×220mm

12. The heating temperature can be up to 500 ℃

13. Standard volume of liquid injector: 20 ml

14. Liquid injection pump loading: liquid injection device with a diameter not exceeding Ø30mm

15. Liquid injection speed: 0.1mm/min-45mm/min, fine-tuning speed 0.01mm/min-8mm/min

16. Syringe travel distance setting range: 0.001mm-120mm

Product Dimensions:

Main Machine 1550mm×750mm×750mm

Syringe Pump: 250mm×225mm×170mm 

 

 

Warranty

    One year limited with lifetime support (not including rusted parts due to inadequate storage conditions)


recommend
MG-EZ4-S-PP Lab High speed Small Vacuum Spin Coater
MG-EZ4-S-PP Lab High speed Small Vacuum Spin Coater
MG-EZ4-S-SS Lab High speed Small Vacuum Spin Coater
MG-EZ4-S-SS Lab High speed Small Vacuum Spin Coater
MG-EZ4-S-PMMA Lab High speed Small Vacuum Spin Coater
MG-EZ4-S-PMMA Lab High speed Small Vacuum Spin Coater
EZ4-S-PP Laboratory Compact EZ4 Vacuum Spin Coater
EZ4-S-PP Laboratory Compact EZ4 Vacuum Spin Coater